Water Pump 2P0661 1727775 1673C D333C 3306 Engine 920 930 950

Water Pump 2P0661 1727775 1673C D333C 3306 Engine 920 930 950

Product Description

Product advantages

1. The water pump impeller adopts the raw material Seiko pure aluminum leaf
2. Using imported high-quality bearings
3. Use high quality seals to ensure no water leakage
4. Original 1:1 mold opening design and manufacture, no deviation in size, accurate hole position
5. The water pump shaft adopts VG drill steel, pure fluorine rubber oil seal

Our advantages

1.We provide genuine quality and OEM

2.Products provided can be customized

3.Provide the original part number can be queried by the system

4.Each product has a warranty period

5.The best and more professional service and after-sales service

6.We have enough inventory,no matter when you make order ,we can ship goods as soon as possible

The five-star service we give you

• Specialized in excavator spare parts for more than 15 years.
• 100% quality assurance, development and manufacturing follow the original.
• All products have warranty, monitor driver, 1 year warranty.
• Our driver is programmed and you can use it directly.
• Quick response within 24 hours.
• Provide spare parts for large excavators.
• Positive feedback from customers in overseas markets

• Proper welding procedures are necessary in order to avoid damage to the Electronic Control Module (ECM), sensors, and associated components. Also consider components that are for the driven equipment. Remove the component that requires welding. When welding on an engine that is equipped with an ECM and removal of the component is not possible, the following procedure must be followed. This procedure provides the minimum amount of risk to the electronic components.
• Stop the engine. Remove the electrical power from the ECM.
• Ensure that the fuel supply to the engine is turned off.
• Disconnect the negative battery cable from the battery. If a battery disconnect switch is installed, turn the switch to the OFF position.
• Disconnect all electronic components from the wiring harnesses. Electronic components include the following components:
• Electronic components for the driven equipment
• Engine ECM
• Sensors
• Do NOT use electrical components (ECM or sensors) or electronic component grounding points for grounding the welder.
• When possible, connect the welder ground clamp directly to the engine component that will be welded. Place the clamp as close as possible to the weld. A close connection will reduce the possibility of welding current damage to the engine bearings, to the electrical components, and to other components.
• Protect the wiring harnesses from welding debris and/or from the welding spatter.
• Use standard welding procedures to weld the materials together.

More related products you are looking for

1727773 PUMP GP-

1727772 PUMP GP-

1727770 PUMP GP-

1727761 PUMP GP-

1727759 PUMP GP-

1727475 PUMP-HYDRAULIC

1729768 PUMP AS

1729321 PUMP GP-MTRG-

1727780 PUMP GP-

1727778 PUMP GP-

1727777 PUMP GP-

1727776 PUMP GP-

Water pump failure performance

1. Unstable idle speed:
The failure of the water pump can cause the rotational resistance of the water pump to increase.

2. There will be noise in the engine part:
This sound is a rolling friive, similar to the sound of "boom boom boom".
This sound can be accelerated as the engine rotates and changes in volume
change. This noise generally increases with the severity of the fault
increasingly obvious.

3. Cooling system failure
1) Hot air is not hot
The most overlooked phenomenon caused by lack of flow. Engine water in winter
After warming up,
The hot wind cannot blow out, and inexperienced people even think that
The car is dead, it's time for a replacement. In fact, just replace a small water pump.
All can solve the problem.

2) Engine water temperature is unstable:
The performance is that the engine water temperature indior needle fluctuates within a certain range. The reason is
The water temperature in the small cycle is inconsistent due to the lack of circulation. On the one hand, it leads to
The opening temperature of the thermostat increases, on the other hand, after the high temperature water flows out, the low temperature
The water quickly flows to the thermostat, causing the thermostat to close quickly. Under normal conditions
After warming up, the water temperature of the engine will remain at a relatively constant
level, approximately at 93°C.

3) The cooling water is reduced, the large circulation is not smooth, and the engine is high temperature:
At this point, the pump has been relatively serious damage. If you continue
Driving will directly lead to increased engine damage.

FAQ

Q1. Which shipment can you supply?

A1: By sea, by air or by express(DHL, Fedex, TNT, EMS, UPS, etc).

Q2. What is your terms of packing?

A2: Generally, we pack our goods in neutral cartons or wooden boxes. If you have legally registered patent, we can pack the goods in your branded boxes after getting

your authorization letters.

Q3. What payments are available?

A3: T/T , Western Union, Trade assurance, L/C.

Q4. What is your terms of delivery?

A4: EXW, FOB, CFR, CIF.

Q5. How about your delivery time?

A5: Generally, it will take 1 to 3 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

Q6. What is your sample policy?

A6: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample fee and the courier cost.

Q7. Do you test all your goods before delivery?

A7: Yes, we have 100% test before delivery.

Q8: How do you make our business long-term and good relationship?

A8:1. We keep good quality and competitive price to ensure our customers benefit .

2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.

Q9: How can i trace my order?

A9: We'll send you the Bill of Lading or express tracking number once it comes out.

Water Pump 2P0661 1727775 1673C D333C 3306 Engine 920 930 950 Images